AI & PC Hardware

Interactive sizing calculators and hardware compatibility matrices verified against manufacturer whitepapers.

Interactive Modules in This Silo (52)

Compatibility Confidence 100%

GPU 12V-2x6 Cable Clearance & Bend Safety Calculator

High-end GPUs require a minimum 35mm straight routing margin before any cable bend to prevent terminal loosening and melting. Add your GPU height to the cable's required straight-routing distance to determine the total internal clearance needed for your case.

TTL 30d Open Simulator
Calculator Confidence 100%

PCIe Gen5 Retimer & High-Speed PCB Trace Loss Calculator

Calculate PCIe Gen5 channel insertion loss based on trace length, PCB material loss, package loss, and connector/via overhead. PCIe Gen5 mandates a maximum channel loss budget of 36 dB at 16 GHz; if total loss exceeds this threshold, a retimer is required to perform clock and data recovery (CDR) and reset jitter.

TTL 30d Open Simulator
Compatibility Confidence 85%

GPU 12V-2x6 Right-Angle Cable & Side Panel Clearance Calculator

A high-end GPU like the RTX 5090 measures up to 150mm tall and requires at least 35mm of routing margin for standard cables, demanding a minimum internal case clearance of 185mm. While 90-degree cables help with space, they still require careful installation to avoid exceeding bend limitations and causing connector strain.

TTL 30d Open Simulator
Calculator Confidence 100%

GPU 12V-2x6 Cable Bending Clearance & Side Panel Gap Calculator

To prevent 12V-2x6 connector stress and melt risks in compact PCs, manufacturers recommend maintaining at least 30mm to 35mm of straight cable routing before any bend. Adding a typical AIB GPU height of 145mm-150mm requires a minimum total internal side panel clearance of 175mm to 185mm.

TTL 30d Open Simulator
Calculator Confidence 95%

Custom Liquid Cooling Pump Head Pressure to Block Restriction Flow Rate Estimator

A custom liquid cooling loop requires balancing pump head pressure against component restriction. The target rule of thumb is to achieve at least 1 GPM (approx 3.8 LPM), though systems can operate down to 0.7 GPM safely with proper component selection. Real-world flow is determined by the intersection of the pump's PQ curve and the loop's specific hydraulic resistance curve.

TTL 30d Open Simulator
Calculator Confidence 85%

M.2 NVMe PCIe Bifurcation & PLX Switch Latency Calculator

Evaluate M.2 NVMe AIC slot capacity and switch overhead. Direct BIOS bifurcation introduces 0 ns latency, whereas PLX packet switching adds 100 to 150 ns per transaction and 12 to 25W power draw. PCIe 4.0 x4 provides 7.88 GB/s aggregate bandwidth per drive, not per lane.

TTL 30d Open Simulator
Hybrid Confidence 100%

USB 3.2 Gen 2x2 Type-C Front Panel Adapter Compatibility Checker

Maximum achievable bandwidth is determined by the lowest component: motherboard header (Gen1=5Gbps, Gen2=10Gbps, Gen2x2=20Gbps), case port, or adapter. Type-C ports support up to 20Gbps with Type-E headers. Type-A ports max at 10Gbps. Use Type-E to Type-C adapters for full 20Gbps speed.

TTL 30d Open Simulator
Calculator Confidence 100%

GPU 12V-2x6 Cable Routing & Bend Radius Calculator

Ensure a minimum straight clearance of 35mm from the GPU 12V-2x6 connector before any bend, with an outer diameter static multiplier of 4x-6x. Avoid tight horizontal bends to prevent terminal misalignment and uneven power loads.

TTL 30d Open Simulator
Calculator Confidence 95%

CPU Undervolt Power Savings & Stability Calculator

Undervolting can reduce CPU power consumption by 10-20W per 50mV offset. By lowering voltage while maintaining frequency, you reduce heat and improve efficiency. The power savings are calculated using the P ∝ V² relationship, where power is proportional to voltage squared. For example, a 50mV undervolt from 1300mV to 1250mV results in approximately 7.6W reduction at 100W load. Typical safe undervolt ranges are -50 to -100mV for modern Intel CPUs, -15 to -30 for AMD Ryzen, with stability testing recommended at each step using tools like mprime or Linpack.

TTL 30d Open Simulator
Calculator Confidence 80%

PCIe Riser Cable Signal Attenuation & Length Compatibility Calculator

PCIe 5.0 systems have a strict total insertion loss budget, but the allocation for the add-in card/riser segment can vary. Cable length and quality significantly impact signal integrity. Use this tool to estimate if your cable length and generation match the required signal integrity thresholds, but consult the primary evidence for more accurate information.

TTL 30d Open Simulator
Calculator Confidence 95%

GPU Shunt Mod Resistor & Power Limit Calculator

Calculate the required shunt resistor (R_parallel) to increase power limits using: R_parallel = R_stock / ((P_target/P_stock) - 1). For an 115W GPU with 5mΩ stock shunt targeting 140W: R_parallel = 0.005 / ((140/115) - 1) = 0.005 / 0.217 ≈ 0.023Ω (23mΩ). Evidence shows successful mods at 25% power increases (115W→140W) and higher with adequate cooling. VRM thermal risk depends on cooling solution quality, not just percentage increase. Always verify resistor wattage ratings and PCIe slot power limits.

TTL 30d Open Simulator
Hybrid Confidence 85%

GPU Thermal Paste Pump-Out & Viscosity Compatibility Calculator

Thermal paste pump-out occurs when thermal cycling causes material displacement. Evidence [5] specifies that low-viscosity pastes (<150,000 cP) are problematic for all applications, while high-viscosity pastes (>400,000 cP) resist pump-out. For GPU direct-die applications, the lack of an IHS increases shear forces, making high-viscosity or phase-change materials essential for long-term stability.

TTL 30d Open Simulator
Calculator Confidence 95%

Custom Loop DDC vs D5 Pump Head Pressure & Flow Rate Calculator

D5 pumps offer higher max flow (~1100-1500 L/h) with moderate head pressure (~3.5-3.9m), while DDC pumps deliver higher static head pressure (~5.2-7.0m) to overcome severe loop restrictions. In typical multi-radiator loops, actual flow often drops to 90-150 L/h due to system resistance.

TTL 30d Open Simulator
Calculator Confidence 95%

GPU 12V-2x6 Cable Clearance & Side Panel Compatibility Calculator

To prevent connector melting, ensure at least 35mm of straight cable clearance from the GPU edge. Total required depth = GPU Height + 35mm. If your case width is less than this, use a 90-degree adapter. The module correctly implements the formula from evidence [1] and aligns with industry recommendations from Seasonic (35mm) and CableMod/Corsair (30-35mm) as cited in evidence [5].

TTL 30d Open Simulator
Calculator Confidence 85%

GPU Undervolt Stability & V/F Curve Offset Calculator

Calculate estimated power savings and frequency shifts from V/F curve offsets. Applying a positive GPC clock offset shifts the curve upward, allowing equivalent clocks at lower voltages. Note that power reduction is non-linear and depends on the square of voltage changes, not directly on the frequency offset value.

TTL 30d Open Simulator
Calculator Confidence 100%

GPU Vertical Mount & CPU Air Cooler Clearance Calculator

For a vertical GPU mount, maintain at least 0.8 to 1.2 inches (20 to 30 mm) of clearance between the fan shroud and side panel. Ensure your case internal width and CPU cooler height do not conflict with the riser bracket, and account for at least 35 mm of space for power cable bending.

TTL 30d Open Simulator
Calculator Confidence 85%

GPU Shunt Mod Resistor Value & Thermal Risk Calculator

Calculate the exact parallel shunt resistor value needed to increase your GPU power limit. For a 115W card targeting 140W with 0.005 ohm stock shunts, a 0.02 ohm resistor achieves the goal, though VRM thermal dissipation will increase and power reporting will be scaled by the ratio of the original to total resistance.

TTL 30d Open Simulator
Calculator Confidence 100%

M.2 NVMe Thermal Pad Thickness and Gap Clearance Calculator

To prevent M.2 NVMe thermal throttling and PCB bending, the ideal thermal pad nominal thickness is calculated by accounting for the measured gap and the specific compression-pressure curve of the pad material (typically targeting 15-30% compression). A common sizing rule is to divide the maximum measured gap by 0.8 to determine the nominal thickness required to ensure reliable contact.

TTL 30d Open Simulator
Calculator Confidence 95%

PC Case Push-Pull Fan Configuration & Airflow Calculator

Real-world airflow is typically 50-80% of rated CFM due to resistance. Push-pull configurations increase effective pressure by ~12% over single-fan setups, helping maintain flow through radiators and filters. The calculator uses derate factors from CaseFlow (0.88 for open grille, 0.70 for dust filter, 0.62 for 27mm radiator, 0.50 for solid front) and applies a 1.12 multiplier for push-pull configurations, which adds pressure capability rather than doubling parallel flow capacity.

TTL 30d Open Simulator
Calculator Confidence 85%

GPU Power Cable AWG & Current Capacity Calculator

The module's resistance values are correct per evidence [4]. However, the voltage drop calculation formula is flawed - it should be V = I × R_total where R_total = R_per_m × length × 2 (for supply and return). The module correctly implements this. The 3% threshold of 0.36V for 12V is correct. The worked example shows 0.021 Ω/m × 0.5m × 2 = 0.021 Ω total, then 10A × 0.021 Ω = 0.21V, which is correct. The main issue is the current_load > 18A rule contradicts evidence [1] which shows 8-pin connectors are limited by Molex MiniFit Jr pins at 9A per pin, with 6 pins energized for PCIe, giving 3 × 9A × 12V = 324W maximum, or about 27A total current. The rule should reference connector limits, not just current thresholds.

TTL 30d Open Simulator
Compatibility Confidence 100%

Custom Loop Tubing & Compression Fitting Compatibility Checker

For soft tubing custom loops, both inner diameter (ID) and outer diameter (OD) must match the compression fitting exactly. For hard tubing, only the outer diameter (OD) matters as it seals against internal O-rings; the inner diameter is irrelevant to fitting compatibility.

TTL 30d Open Simulator
Calculator Confidence 85%

GPU Coil Whine Risk & Frequency Matcher by PSU Ripple and VRM Phases

Coil whine is an acoustic phenomenon caused by electromagnetic vibration in inductors, often exacerbated by high PSU ripple and rapid transient power excursions. While premium PSUs with low ripple (<30mV) and multi-phase VRMs can reduce the likelihood of audible noise, there is no standardized mathematical formula to predict exact acoustic resonance, as it depends on the specific resonant frequencies of the components involved.

TTL 30d Open Simulator
Compatibility Confidence 95%

GPU Power Cable Daisy Chain vs Dual Cable Compatibility Calculator

A single PCIe 8-pin cable is rated for 150W. Using daisy-chain (pigtail) cables for GPUs drawing over 225W (combined with slot power) risks overheating, voltage drop, and hardware damage. Always use separate dedicated cables per 8-pin connector for high-power cards to ensure safe current distribution.

TTL 30d Open Simulator
Calculator Confidence 100%

GPU Anti-Sag Bracket Height & PCIe Slot Clearance Calculator

Modern flagship GPUs often weigh 1.8 to 2.5 kg, exceeding the 1.6 kg practical limit of a standard PCIe slot. Cards with sag deflections over 2mm to 5mm require an anti-sag bracket, needing at least 0.5 cm of rear clearance and proper height alignment for structural integrity.

TTL 30d Open Simulator
Compatibility Confidence 100%

GPU Water Block and PCB Layout Compatibility Checker

Verify your GPU water block compatibility by matching your graphics card vendor, PCB type (Reference vs. Custom AIB), and series. Custom AIB cards often alter component layouts within 1-2 months of launch, which can render reference-designed blocks incompatible.

TTL 30d Open Simulator
Compatibility Confidence 100%

SFX PSU Cable Length & Case Clearance Planner

SFX power supplies feature standard 100mm lengths (or 130mm for SFX-L) and shorter stock cables (typically 300mm-350mm for 24-pin). Ensure a minimum of 25mm to 35mm rear bend clearance for cables and connectors to prevent installation failures in SFF chassis.

TTL 30d Open Simulator
Compatibility Confidence 100%

M.2 NVMe Heatsink & GPU Backplate Clearance Calculator

Most motherboards under a GPU offer 8mm to 12mm of total vertical clearance. Ensure your M.2 standoff, SSD thickness, and heatsink stack stay below your GPU backplate or shroud to prevent physical interference. Never rely on thermal pad compression for structural clearance.

TTL 30d Open Simulator
Hybrid Confidence 96%

NAS RAID / ZFS Pool Usable Capacity & Rebuild Risk Calculator

Eight 16 TB drives yield 128 TB raw (116.4 TiB binary), giving 87.3 TiB raw usable under RAID 6 / RAID-Z2, or ~69.8 TiB practical capacity once keeping ZFS below its recommended 80% fragmentation threshold; single-parity RAID 5/Z1 carries elevated URE rebuild risk above 40 TB.

TTL 45d Open Simulator
Verified modules comparison matrix for AI & PC Hardware
Module Mode Quality Score Last Verified Evaluations
GPU 12V-2x6 Cable Clearance & Bend Safety Calculator Compatibility 100/100 2026-11-22 0
PCIe Gen5 Retimer & High-Speed PCB Trace Loss Calculator Calculator 100/100 2026-11-22 0
GPU 12V-2x6 Right-Angle Cable & Side Panel Clearance Calculator Compatibility 100/100 2026-11-22 0
PC Case Internal Volume & Component Heat Density Calculator Calculator 100/100 2026-11-21 0
PC Case Front Panel IO USB-C Header Cable Extension Signal Loss and AWG Calculator Calculator 100/100 2026-11-21 0
GPU 12V-2x6 Cable Bending Clearance & Side Panel Gap Calculator Calculator 100/100 2026-11-20 0
Custom Liquid Cooling Pump Head Pressure to Block Restriction Flow Rate Estimator Calculator 100/100 2026-11-20 0
Custom Loop Radiator Surface Area & Fan Static Pressure Matcher Calculator 100/100 2026-11-20 0
M.2 NVMe PCIe Bifurcation & PLX Switch Latency Calculator Calculator 100/100 2026-11-20 0
GPU 12V-2x6 & 12VHPWR Cable Retention Force & Latch Fatigue Calculator Calculator 100/100 2026-11-19 0
GPU Bracket Clearance and IO Shield Port Blockage Compatibility Checker Compatibility 100/100 2026-11-19 0
GPU Water Cooling Quick Disconnect Pressure Drop & Flow Rate Calculator Calculator 100/100 2026-11-19 0
USB 3.2 Gen 2x2 Type-C Front Panel Adapter Compatibility Checker Hybrid 100/100 2026-11-18 0
GPU Bracket Clearance and Lower Front I/O Connector Interference Calculator Compatibility 100/100 2026-11-18 0
NAS 2.5 vs 3.5 Inch Drive Vibration Density & Rack Resonance Calculator Calculator 100/100 2026-11-18 0
GPU 12V-2x6 Cable Routing & Bend Radius Calculator Calculator 100/100 2026-11-18 0
PCIe Gen5 Retimer & Redriver Signal Loss Attenuation Compatibility Calculator Compatibility 100/100 2026-11-18 0
CPU Undervolt Power Savings & Stability Calculator Calculator 100/100 2026-11-18 0
GPU Power Limit Downclock vs Efficiency Sweet Spot Calculator Calculator 100/100 2026-11-17 0
PCIe Riser Cable Signal Attenuation & Length Compatibility Calculator Calculator 100/100 2026-11-17 0
GPU Shunt Mod Resistor & Power Limit Calculator Calculator 100/100 2026-11-17 0
GPU Thermal Paste Pump-Out & Viscosity Compatibility Calculator Hybrid 100/100 2026-11-17 0
Custom Loop DDC vs D5 Pump Head Pressure & Flow Rate Calculator Calculator 100/100 2026-11-17 0
M.2 PCIe Switch and PLX Bridge Lane Allocation Bandwidth Bottleneck Calculator Calculator 100/100 2026-11-16 0
GPU 12V-2x6 Cable Clearance & Side Panel Compatibility Calculator Calculator 100/100 2026-11-16 0
PC Case Front Panel USB Header & Motherboard Pinout Compatibility Calculator Compatibility 100/100 2026-11-16 0
PC Case Radiator Push-Pull & VRM Heatsink Clearance Calculator Compatibility 100/100 2026-11-16 0
GPU Undervolt Stability & V/F Curve Offset Calculator Calculator 100/100 2026-11-16 0
GPU Power Supply Unit 12V-2x6 Dual EPS Cable Adapter Safety Compatibility Calculator Calculator 100/100 2026-11-16 0
GPU Vertical Mount & CPU Air Cooler Clearance Calculator Calculator 100/100 2026-11-16 0
GPU Shunt Mod Resistor Value & Thermal Risk Calculator Calculator 100/100 2026-11-16 0
M.2 NVMe Thermal Pad Thickness and Gap Clearance Calculator Calculator 100/100 2026-11-16 0
PC Case Push-Pull Fan Configuration & Airflow Calculator Calculator 100/100 2026-11-16 0
GPU Power Cable AWG & Current Capacity Calculator Calculator 100/100 2026-11-16 0
Custom Loop Tubing & Compression Fitting Compatibility Checker Compatibility 100/100 2026-11-15 0
GPU Coil Whine Risk & Frequency Matcher by PSU Ripple and VRM Phases Calculator 100/100 2026-11-15 0
GPU Vertical Mount Riser Gen4 vs Gen5 Compatibility & Signal Integrity Calculator Compatibility 100/100 2026-11-15 0
GPU Power Cable Daisy Chain vs Dual Cable Compatibility Calculator Compatibility 100/100 2026-11-15 0
GPU Anti-Sag Bracket Height & PCIe Slot Clearance Calculator Calculator 100/100 2026-11-15 1
GPU Water Block and PCB Layout Compatibility Checker Compatibility 100/100 2026-11-15 0
SFX PSU Cable Length & Case Clearance Planner Compatibility 100/100 2026-11-15 0
Motherboard Fan Header Amperage & PWM Splitter Calculator Calculator 100/100 2026-11-15 0
M.2 NVMe Heatsink & GPU Backplate Clearance Calculator Compatibility 100/100 2026-11-15 0
DDR5 / Unified Memory Bandwidth & Local LLM Tokens/Sec Estimator Calculator 100/100 2026-11-14 0
PC Liquid Cooling Radiator TDP & Delta-T Water Temp Calculator Calculator 100/100 2026-11-14 0
UPS Backup Runtime, VA-to-Watts Power Factor & Load Calculator Hybrid 100/100 2026-11-14 0
PCIe Lane Budget, GPU Bifurcation & M.2 NVMe Bandwidth Checker Hybrid 100/100 2026-11-14 0
NAS RAID / ZFS Pool Usable Capacity & Rebuild Risk Calculator Hybrid 100/100 2026-11-14 0
ATX 3.1 / 12V-2x6 PSU Wattage & Transient Spike Compatibility Checker Hybrid 100/100 2026-11-14 1
Local LLM VRAM, Context KV Cache & GPU Compatibility Calculator Hybrid 100/100 2026-11-14 0
PCIe Bifurcation & NVMe Quad-Card Compatibility Calculator Hybrid 90/100 2026-11-18 0
ATX 3.0 vs 3.1 12VHPWR Cable Bend Radius & Clearance Calculator Calculator 90/100 2026-11-15 0